Kmc-controls CEP-4703V Manuel d'utilisateur télécharger pdf

CEP-4703/4703V 1 Installation Guide

3.437

[87.3]

1.568 [40]

2.6

[66]

[63.5]

2.5

[63.3]

3.28

[83.2]

2.6

[66]

CEP-4703

CEP-4703V

Removable conduit fitting

with 1/2" NPS threaded hole

Gear

disengagement

lever

Override input (remembers

position and closes valve on

no call

for heat or cool)

Cold water LAT sensor or

hot water setpoint resistor

Cold water setpoint

resistor or hot water

LAT sensor

Sensitivity

adjustment

Terminals

(under cover)

Installation Guide

Analog Electronic DAT Controller-Actuator

CEP-4703/4703V

CEP-4703 Mounting

CEP-4703 Mounting .........................................................................................1

CEP-4703V Valve Mounting .............................................................................2

Wiring Connections .........................................................................................3

Operation .........................................................................................................3

Troubleshooting ...............................................................................................4

No Rotation or Wrong Stroke Range ............................................................4

Wiring Issues ................................................................................................4

Maintenance ....................................................................................................4

Accessories ......................................................................................................4

More Information .............................................................................................4

Important Notices ............................................................................................4

NOTE: Thismountingsectionisspecic

to the CEP-4703. For mounting a

CEP-4703V, see CEP-4703V Valve

Mounting on page 2.

1. Ensure the damper or valve shaft can

move freely through its entire range

of motion, and x any binding before

installing the actuator. Turn the damper

blade to its fully closed position.

2. Press (to the right) and hold the gear

disengagement lever, rotate the actuator

to the fully closed position, and release

the lever.

NOTE: Depending on the damper-seal

design, backing the actuator o

its stop approximately 5° may

provide tight damper shut-o.

3. Align the actuator and slide it onto the

shaft.

4. Leaving a gap between the actuator

and mounting surface to prevent any

binding, nger-tighten the nuts on the

V-bolt.

5. Insert the non-rotation bracket (HMO-

4002 supplied or HMO-4001 “T” bracket

available separately) into the slot at the

base of the actuator (as shown in the

illustration).

6. Secure the non-rotation bracket with

two (2) #8 or #10 self-tapping screws.

7. Evenly tighten the V-bolt nuts 30 to 35

in-lb.

8. If desired, use a 7/64-inch hex key

wrench to loosen and position the end-

stop screw.

NOTE: The two holes at the top of the

actuator are NOT for use in

direct-coupled applications.

They are for remote mounting,

such as with the optional HLO-

4001 Crank Arm Kit (see the Data

Sheet).

Gear disengagement lever

Non-rotation bracket

(HMO-4002)

Mounting surface

Removeable conduit fitting

with 1/2" NPS threaded hole

1 2 3 4

Résumé du contenu

Page 1 - Installation Guide

CEP-4703/4703V 1 Installation Guide3.437[87.3]1.568 [40]2.6[66][63.5]2.5 2.5[63.3] 3.28[83.2] 2.6[66]CEP-4703CEP-4703VRemovable conduit fittingw

Page 2 - CEP-4703V Valve Mounting

CEP-4703/4703V 2 Installation GuideCEP-4703V Valve Mounting3.437[87.3]1.568 [40]2.6[66][63.5]2.5 2.5[63.3] 3.28[83.2] 2.6[66]CEP-4703CEP-4703VRe

Page 3 - Operation

CEP-4703/4703V 3 Installation GuideWiring Connections1. Loosen the screw on the conduit ing and lift up to remove the ing.2. Using a utili

Page 4 - Important Notices

CEP-4703/4703V 4 Installation GuideAccessoriesHCO-1151 Weather shield kitHLO-4001 Crank arm kitHMO-4001 Non-rotation “T” bracketHMO-4002 Rep

Modèles reliés CEP-4703

Commentaires sur ces manuels

Pas de commentaire

Kmc-controls CEP-4703V Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Capteurs Kmc-controls CEP-4703V. KMC Controls CEP-4703V User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés CEP-4703

Commentaires sur ces manuels

Produits connexes et manuels pour Capteurs Kmc-controls CEP-4703V