Kmc-controls THE-1102 Manuel d'utilisateur télécharger pdf

THE-1102 1 Installation Guide

cover. Do not use excessive force and deform or

break the tab.

2. Carefullypullthecoverfromthebase.

Handy Box Installation (Recommended)

1. MountanHMO-6036

wallplatetothehandy

boxusingthetwoscrews

provided.

2. RemovetheTHE-1102’s

coverfromtheblackbase

(seetheLocationand

CoverRemovalsection).

3. Withtheplastictabbuonontheboom,aach

thebasetothebackplateusingthetwoscrews

provided.

4. Connectthewiring(seetheWiringsection).

5. Reinstallthecover.

Hollow Wall Installation

1. RemovetheTHE-1102’scoverfromtheblackbase

(seetheLocationandCoverRemovalsection).

2. Usingthebaseasa

template,drilltwoholes

formountingscrews

(7/64inchesor3mmin

diameterand1.4inches,

1-13/32inches,or35.6mm

apart)andcutacenter

holefortheterminalblock.

3. Withtheplastictabbuonontheboom,aach

thebasetothewallusingtwo#6self-threading

screws.(Plasticanchorsarerecommended,and

thesizeoftheholeswillthenneedadjusting.)

4. Connectthewiring(seetheWiringsection).

5. Reinstallthecover.

Installation Guide

Humidity Transmitter w/ Temperature Sensor

THE-1102

Mounting

Mounting 1

Location and Cover Removal 1

Handy Box Installation (Recommended) 1

Hollow Wall Installation 1

Wiring 2

More Information 2

Maintenance 2

Important Notices 2

Location and Cover Removal

InstalltheTHE-1102onaninsidewallwhereitcan

sensetheaverageroomtemperature/humidityand

beawayfromdirectsunlight,heatsources,windows,

airvents,andaircirculationobstructions(curtains,

furniture,etc.).Itcanbemountedonahollowwall

or(withanHMO-6036)toa2x4inchhandybox.

Thecoverisheldtotheblackbasebythreesmall

pegsthattintheholesofthecover.Theboompeg

isonatabandsnapsintothecenterboomhole.

1. WithasmallPhillipsscrewdriverorhexwrench,

press in and hold the plastic tab buon that

snaps into the center hole on the boom of the

2-1/4" (57 mm)

2-7/16"

(62 mm)

5/8"

(16 mm)

Up (Toward Ceiling

at Installation)

Tab Button

Temperature Output

(10K Thermistor)

Humidity Output

(0 to 5 VDC)

Signal Ground

– Power Ground

(A)

(B)

(C)

(F)

(D)

+ 10 to 15 VDC Power

NOTE: The Thermistor

Temperature

Output

Terminal “A”

should be

at the top of

the terminal

strip aer

installation.

1 2

Résumé du contenu

Page 1 - Installation Guide

THE-1102 1 Installation Guidecover. Do not use excessive force and deform or break the tab. 2. Carefullypullthecoverfromthebase.Handy Box Ins

Page 2 - More Information

Commentaires sur ces manuels

Pas de commentaire

Kmc-controls THE-1102 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Capteurs Kmc-controls THE-1102. KMC Controls THE-1102 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Capteurs Kmc-controls THE-1102